Hai mã hiệu này bản chất khác nhau hoàn toàn. Lý do bạn băn khoăn là gì vậy?
Xem bảng in
- AD.25121 là định mức cho công tác lu lèn mặt đường cũ sau cày xới. Như vậy về mặt yêu cầu kỹ thuật hay tính chất công viêc cho các trường hợp đắp mặt đường hay san nền mà có chiều dày lớp đắp > 30 cm dùng cho trường hợp này theo tôi là không thỏa đáng.
- Trong trường hợp chiều dày đắp lớn, khối lượng đắp lớn thì dùng mã AB.64112 là hợp lý.
Vấn đề cần bàn ở đây theo mình nghĩ là đào nền đường và lu lèn lại nền hạ (trước khi tiến hành đắp đất móng, mặt đường). Nếu đúng như vậy thì các bạn nên dùng mã hiệu AD.25121 và phần máy phân tích ra chỉ dùng ô tô tưới nước 5m3 và máy đầm 25T là phù hợp với tính chất công việc. Mong các bạn có ý kiến thêm!
Anh em diễn đàn cho hỏi chút! Trước kia khi còn học đại học, các giáo trình về thi công đều nói lớp đắp có chiều dày hợp lý là 30 - 50 cm. Tuy nhiên khi tra trong các tiêu chuẩn, quy phạm thì chưa thấy có. Có bác nào biết tiêu chuẩn, quy phạm nào quy định về việc này chỉ giúp e với !
Xin cảm ơn!
Xin tham gia vài lời với bạn thế này..
1. Về mặt chuyên môn: khi người ta thường nói "lớp đắp có chiều dày hợp lý là 30 - 50 cm" nghĩa là trong chuyên môn về thiết kế kết cấu áo đường thì chiều sâu để ứng suất tác dụng của tải trọng bánh xe còn có thể gây ra cho nền đường là khoảng như vậy. nếu sâu quá thì ứng suất này quá nhỏ và tiệm cận về 0..như vậy tải trọng đầm nén (công đầm) còn có nghĩa gì nữa đúng không. còn nếu lớp đắp quá mỏng thì chính cái anh ứng suất này (công đầm) lại có nguy cơ gây phản tác dụng là làm phá vỡ kết cấu vật liệu đắp.
2. Về mặt pháp lý: thì trong tiêu chuẩn thiết kế và thi công đường bao giờ cũng qui định về độ chặt và các chỉ tiêu khác cho các lớp mà..bạn chịu khó đọc nhé (22TCN 221;211;334...v.vv...) hoặc trong thi công đắp nói chung TCVN 4447..v.v....đọc thật kỹ vì có khi họ chỉ thể hiện trong 1 vài dòng thôi. Chúc thành công
Về kỹ thuật thi công thì nói và bảo vệ ok. Tuy nhiên, điều tôi cần là một tiêu chuẩn nào đó, nói chính xác như vậy bạn ạ. Tôi đang gặp tình huống tranh cãi cần chứng cứ cụ thể mà. Chứ ngồi phân tích kỹ thuật thì tôi cũng hiểu điều bạn nói. Nhưng cãi với người không hiểu, không biết, người ta chỉ cần đưa ra cái tiêu chuẩn nào quy định và có con số đó thôi bạn. Tôi cần là cần cái đó.
đường bê tông nông thôn
đắp cát dày 5-10cm thì có cần lu lèn độ chặt ko mấy bác
Của bạn đây:
Thi công và nghiệm thu kết cấu áo đường bằng cấp phối thiên nhiên
ThânTrích dẫn:
Tuỳ thuộc phương tiện lu để san rải cấp phối bằng máy san hoặc máy rải ứng với chiều mỗi
lớp (đa lu lèn chặt) nhưng không được quá 20cm. Thao tác và tốc độ san rải sao cho tạo bề mặt
bằng phẳng, không gợn sóng, không phân tầng và hạn chế số lần qua lại không cần thiết của máy.
Thì tôi chả liệt kê ra cho bạn 1 loạt tiêu chuẩn rồi còn gì!!! mỗi loại vật liệu khác nhau khi đắp bạn phải đọc tiêu chuẩn về nó..ví dụ đắp nền bằng cấp phối đồi thì đọc tiêu chuẩn về cấp phối thiên nhiên, đắp bằng cát hay cấp phối đá dăm cũng tương tự chứ làm sao mà trích dẫn hết được trong vài dòng này..các bạn trong diễn đàn đã nêu 1 số rồi đó..chúc thành công nhé (nên đọc cả tiêu chuẩn thiết kế và thi công thì sẽ đầy đủ cơ sở để mà đối đáp với "người không biết" của bạn nhé)...chúc thành công